If you've recently had your car coated and noticed some patchy or uneven marks on the surface, then don?t panic. You?re likely looking at what professionals call high spots. These are common during the application process and can be corrected.
In this guide, we?ll explain how to remove ceramic coating high spots without damaging your car?s finish. This is an important part of proper ceramic coating care, especially if you're searching for ceramic coating near me in Appleton or considering a DIY route.
What Are High Spots in Ceramic Coating?
High spots are uneven patches that form when too much ceramic coating is left on the paint surface. Instead of bonding smoothly, the excess coating hardens, leaving behind a dark, sometimes sticky or shiny area. These imperfections can appear as streaks, smudges, or patches, especially visible under bright lighting or sunlight. The earlier you notice them, the easier they are to fix.
Why Do High Spots Happen?
High spots usually occur when the coating isn?t levelled or wiped off properly during application. This might happen if:
- The product isn?t buffed in time before it starts curing
- The microfiber towel used is dirty or not absorbent enough
- The application is uneven or rushed
Even professionals sometimes face this, so if it happened to you, it?s completely normal. The key is addressing it correctly.
How to Remove High Spots from Ceramic Coating?
Wondering just how to get rid of bumps or rough spots from ceramic coating? Timing is everything. If the high spot is still wet (within a couple of hours of putting it on), you can take a clean and dry soft towel and softly rub it off. Apply a bit of pressure and move the clippers around in small circles. Often, just a simple act of giving can make a big difference.
If the coating has started to dry, you may need to use something stronger to take it off. Use a very light sanding pad or a special detailing cloth with a very mild polishing cream on it. Work slowly and gently on the high part. This will help remove the extra paint, but won?t take off all of the coating at once. After this, you can put on another thin coat of ceramic coating over the spot you covered to make sure the protection is even again.
Don?t Wait Too Long: Timing Is Crucial
It?s always best to tackle high spots early. If they?re left for too long, they harden completely and may require more aggressive polishing or even paint correction. That?s why daily inspection after application matters. The first 24 hours are critical to catch any imperfections while they?re still soft and easy to fix.
What If You Can?t Remove It?
If you?ve tried and the mark still doesn?t budge, it might be time to consult a professional. For drivers in Wisconsin, Muntz Tintz offers expert solutions. Just search for ceramic coating near me in Appleton, and we?re here to help. Fixing high spots professionally can restore the look without harming the surrounding surface.
Do You Need to Remove the Whole Coating?
This is a common concern. Thankfully, in most cases, you don?t need to remove the entire ceramic layer. If the high spot is isolated and small, you can spot-correct and reapply in that area only. Just ensure the transition between the old and new layer is smooth. Patience and gentle technique make a big difference.
Still Deciding Between Coatings?
If you?re comparing finishes and not sure what?s right for your vehicle, check out our full breakdown on ceramic coating vs powder coating: know differences. It will help you understand the unique advantages of each and make a smarter decision for long-term car care.
Keep Ceramic Tint?s Good Name
Durable and strong, ceramic coatings are also well-known for giving your car a superb shine. If you have difficulties at a certain point, don?t let it stop you from finishing your application. All these tend to happen, but they can be easily solved with proper attention. Still, there is no reason not to take advantage of ceramic coatings just because there are a few negatives associated with them.
Ensuring Your Finish Looks Good Even After Filing
After you?ve finished, make sure to keep your paint in good shape. It is best not to wash the car for the next few days. Let the coating cure fully. Do not park in places that are too bright or too shaded. Moreover, after complete curing, wash the surface with a pH-balanced car shampoo and use a soft mitt. It allows you to maintain the shine and quality of your paintwork.
Conclusion
High spots can happen, but they don?t have to ruin the sleek look of your vehicle. Knowing how to remove ceramic coating high spots gives you the confidence to handle small issues without stress. If you?re unsure or if you just want the job done perfectly the first time, trust the professionals at Muntz Tintz.
We?re your local experts for ceramic coating near me in Appleton and can ensure a smooth, durable finish every time. Ready to give your car a flawless ceramic coat?
Contact us today and experience the Muntz Tintz difference. Get Your FREE Quote Today or contact us at 920-734-3001 today!